condor d.c. power supplies, inc., a subsidiary of sl industries, inc. 805-486-4565 ?(800) 235-5929 fax: (805) 487-8911 http://www.condorpower.com model pwr output #1 output #2 output #3 output #4 NMX-503-0512 500 +5v @ 75a +12v @ 8/12a pk -12v @ 4a nmx-504-1205 500 +5v @ 75a +12v @ 8/12a pk -12v @ 4a 5.2v @ 5a nmx-504-1212 500 +5v @ 75a +12v @ 8/12a pk -12v @ 4a 12v @ 5a nmx-504-1224 500 +5v @ 75a +12v @ 8/12a pk -12v @ 4a 24v @ 3a nmx-504-1512 500 +5v @ 75a +15v @ 4a -15v @ 4a 12v @ 5a nmx-504-1524 500 +5v @ 75a +15v @ 4a -15v @ 4a 24v @ 3a 500 watts power factor corrected multiple output, forced current sharing standard nmx series nmx-500 featuring: forced current sharing for n +1 redundancy remote sense on outputs #1 and 2 universal ac input 0.99 typical power factor dual converter design eliminates interaction between logic and auxiliary outputs low ripple and noise on all outputs dc power good and ac power fail signals true remote inhibit monotonic turn-on and turn-off the smallest, most capable 500 w power supply of its kind. overload-, overvoltage-, thermal-pro- tection and integral covers are standard. all nmx power supplies can be ordered self-cooled with internal ball-bearing fans. the nmx 350 and nmx 500 are available without fans for use with system air cooling. all outputs are oem-adjustable and 3 v main outputs are available. option v integral rfi filters allow every nmx power supply to meet conducted emissions of en55022 class b and fcc class a. compliance is also provided for interna- tional safety requirements including iec 950 and the requirements of iec 555-2 for harmonic line distortion. model pwr output #1 output #2 nmx-502-0512v 500 +5v @ 30a +12v @ 30/40apk mass storage nmx-502 series* *contact factory for detailed mechanical and electrical specifications. the drawings on opposite page do not represent this nmx product. the nmx-502 features dual bus-bar outputs and integrated ??option. see dmx 500 for dc input equivalent
condor d.c. power supplies, inc., a subsidiary of sl industries, inc. 805-486-4565 ?(800) 235-5929 fax: (805) 487-8911 http://www.condorpower.com function 115 vac 230 vac connector tb1- line line 1 tb1- neutral line 2 tb1- safety ground safety ground ac input (90-264 vac continuous range) function location notes connector output #1 terminal marked +v main output terminal marked -v rtn (common) output #2 j1-5, 10 j1-4, 9 rtn (common) output #3 j1-3, 8 j1-4, 9 rtn (common) output #4 j1-2, 7 (+) floating output j1-1, 6 (? floating output dc output amp #770743-1 mates with connector #770580-1 with sockets #171639-1 (awg #20 to #16) bus bars #8-32 screws barrier strip #6-32 screws 3/8?centers function location notes connector remote sense j2-2 output #1 sense j2-1 output #1 sense rtn j2-8 output #2 sense j2-7 output #2 sense rtn dc power good j2-3 reference to ac power fail j2-4 common inhibit j2-5 current share j2-6 aux. fan voltage j3-1 +12v @ 0.5a output (not available with j3-2 rtn (common) ??or ??options) status and control amp mta type #640456-8 pin header (locking) specifications: all models input ac input: 90-264 vac continuous range, 47 to 63 hz. internally fused for 10 a. power factor: 0.99 typical at full load. meets en61000-3-2. inrush: cold start ac current is less than 30 a at 115 vac and 60 a at 230 vac. limited by thermistor. brownout protection: holds regulation to 85 vac. holdup time: 20 ms minimum after removal of power at full load. efficiency: 75% typical. ac power fail: provides ttl ?? 5 ms before output voltage goes out of regulation band upon loss of ac power. output adjustability: outputs #1 and 2 user adjustable ?% minimum. output #3 tracks #2; initial accuracy ?%. output #4 user adjustable ?% minimum, or +5% only if voltage is 5.2 v line & load reg: outputs #1, 2, and 4 hold ?% over ac input range and 0 to 100% load change. output #3 requires 20% minimum load on outputs #2 and 3 to hold ?%. ripple & noise: less than 1% p-p or 100 mv, whichever is greater. remote sense (outputs #1 and 2) : compensates for 250 mv total line drop. open sense lead protection. (see redundancy, below.) temperature coefficient (outputs #1, 2, and 4) : 0.02% per degree c. stability: 0.1% over 8 hours after 30 minutes warm-up. transient response (outputs #1, 2, and 4) : output voltage returns to within 1% in less than 500 ? for a 50% load change. peak transient does not exceed 5%. overload protection: all outputs are protected against overload and short circuit. automatic recovery upon removal of fault. overvoltage protection (outputs #1 and 2) : protects load against power supply induced overvoltage. trip point is factory set so that output voltage cannot exceed 136% of nominal. peak output current: dual current ratings define continuous and peak currents. the peak current shown can be delivered for a maximum period of 30 seconds. remote inhibit: contact closure to the negative sense line or a ttl level ??turns off dc outputs. dc power good: provides a ttl ??open collector when output #1 is above 4.6 v nominal. redundancy: external or-ing diodes and forced current sharing on output #1 provide ?+1? capability. remote sense (+s) compensates for additional 0.6 v diode voltage drop. when the current sharing terminal is connected between units, current sharing remains within 10% of the unit s full output current rating. for hot swap applications see tmx 350. reverse voltage: protected against reverse voltage up to supply current rating. environmental thermal protection: shuts down power supply if overheated. automatic recovery. temperature range: 0 to 50? at full ratings. safety agencies: most models are approved to ul1950; csa 22.2 #234; iec 950 and t?v en60950, class 1 selv., ce 72/23/eec/93/68eec (low voltage directive). conducted rfi: meets fcc part 15, subpart j, class a; en55022 class b; cispr 22 class b. output isolation: isolated from ground 50 vdc. cooling: 30 cfm required to achieve full ratings. amp mta type #640456-2 pin header (locking) nmx-500 3.7 lbs - 1.7 kgs 500 watts 9.65 x 5 x 2.05 nmx-500 (l) (n) ( ) nmx-500 with option f 3.9 lbs - 1.8 kgs dimensions: inches millimeters options: option ?? fan/cover assembly: cover with integral ball-bearing fan provides proper cooling to achieve full ratings at 50? ambient temperature. 2.05?dimension increases to 3.28? option ?? fan/cover assembly: low profile, end venting cover with integral ball-bearing fan. 2.05?dimension increases to 2.50? and 9.65?dimension increases to 11? consult factory for other available options.
|
